chrisheltra
04-03-2008, 07:05 AM
This guy is local too so shipping will be non existant.
well here it is... the proto!!!
it is 18gauge .047" thick stainless steel.. i also put a #3 polish on it after it was cut for a nice finish.. the grain runs from east to west....
it turned out pretty good... i just need to know if you guys want me to roll with this design.. a lot less material involved with this than there was in the cobras i was making as you can see by the photo with both of them in it which will result in a lower price than the cobras were....
in the last photo i am showing the only point in which the logo appears to be "weak" (which happens to be between the first N and the I) which if it is flat on a wall should not matter AT ALL!!! i am using force to make it separate like that.... just holding it regularly does not produce that kind of deviation..... the small one will have to be manipulated a little as that flimsiness will be more pronounced when it is scaled down... i have not cut a small one out yet...
this one turned out to be 23 inches long and roughly 4 inches tall....
thanks for any and all feedback... let me know what you guys think and if you are interested.... if the interest is high enough i will start making some later this week that will be for sale and will begin a new thread for the logos.... well here it is
http://img148.imageshack.us/img148/2057/lightninglogo001fw0.jpg
http://img389.imageshack.us/img389/15/lightninglogo002sb6.jpg
http://img510.imageshack.us/img510/3474/lightninglogo004sf9.jpg
http://img394.imageshack.us/img394/6536/lightninglogo003rf0.jpg
http://img503.imageshack.us/img503/729/lightninglogo005ef2.jpg
BT
okay guys... the large one will probably wind up costing 55.99 and the small one which i have not produced yet will be probably cost 20.99... and if you buy both at once you get them both for 65.99.... this is all tentative... NOT SET IN STONE YET!!!!
there will be a new thread made when it comes time to start ordering... so please be advised of that...
as a little note: my uncle passed away yesterday and it is going to put some wrenches in my plans of beginning production this weekend....
so guys, please stick with me... looking at getting them ready for shipment beginning middle of next week or so...
thanks again for all of the interest...
BT
well here it is... the proto!!!
it is 18gauge .047" thick stainless steel.. i also put a #3 polish on it after it was cut for a nice finish.. the grain runs from east to west....
it turned out pretty good... i just need to know if you guys want me to roll with this design.. a lot less material involved with this than there was in the cobras i was making as you can see by the photo with both of them in it which will result in a lower price than the cobras were....
in the last photo i am showing the only point in which the logo appears to be "weak" (which happens to be between the first N and the I) which if it is flat on a wall should not matter AT ALL!!! i am using force to make it separate like that.... just holding it regularly does not produce that kind of deviation..... the small one will have to be manipulated a little as that flimsiness will be more pronounced when it is scaled down... i have not cut a small one out yet...
this one turned out to be 23 inches long and roughly 4 inches tall....
thanks for any and all feedback... let me know what you guys think and if you are interested.... if the interest is high enough i will start making some later this week that will be for sale and will begin a new thread for the logos.... well here it is
http://img148.imageshack.us/img148/2057/lightninglogo001fw0.jpg
http://img389.imageshack.us/img389/15/lightninglogo002sb6.jpg
http://img510.imageshack.us/img510/3474/lightninglogo004sf9.jpg
http://img394.imageshack.us/img394/6536/lightninglogo003rf0.jpg
http://img503.imageshack.us/img503/729/lightninglogo005ef2.jpg
BT
okay guys... the large one will probably wind up costing 55.99 and the small one which i have not produced yet will be probably cost 20.99... and if you buy both at once you get them both for 65.99.... this is all tentative... NOT SET IN STONE YET!!!!
there will be a new thread made when it comes time to start ordering... so please be advised of that...
as a little note: my uncle passed away yesterday and it is going to put some wrenches in my plans of beginning production this weekend....
so guys, please stick with me... looking at getting them ready for shipment beginning middle of next week or so...
thanks again for all of the interest...
BT