new LS1 turbo intake

[Pesce Nero]

my friend Lane Culver is starting production an a new intake he designed. intake has a intercooler in it. he just sent me these pics. thought i would share

http://i40.photobucket.com/albums/e225/sixpackgut/lanes%20stuff/GetAttachment.jpg

http://i40.photobucket.com/albums/e225/sixpackgut/lanes%20stuff/GetAttachment2.jpg

http://i40.photobucket.com/albums/e225/sixpackgut/lanes%20stuff/GetAttachment3.jpg

[BigdaddyDupree]

thats nice.

[clubracergt1]

thats nice.

race truck

[Matts94Z28]

That is nice!

[ASkipper]

what kind of price would that run?

[Pesce Nero]

what kind of price would that run?

are you sitting down?



3K

[ASkipper]

You mind if I post this on a few different forums I am on.

[Pesce Nero]

You mind if I post this on a few different forums I am on.

i dont care. it will probably just be sold thru hinsonsupercars

[BAD BOB]

thats a cool design but the water running through it will have to work extra hard due to heat soak i think

[Harry]

Nice piece. But 3k. WOW.:eek:

[clubracergt1]

3 Grand sounds almost reasonable. Looks like a TON of hours went into fabbing that thing.

[Harry]

I guess some people just have it like that.

[s14.5gonewide]

i assume its using a hear exchanger as well as the built in intercooler..

is it air/water or air/air?
any provisions for a methonal setup?

the price is reasonable for what you are getting.. sheetmetal manifold intercooler.
its a ton of r@d put into it.. looks like the cobra manifold is seen this week.
legit parts:)

[AverageJoe]

Damn, WE might need to get one of these!

[98Camarod]

Damn, WE might need to get one of these!

We'll have to split it between everyone on here. I'll take the third weekend of every month

[itSSlowZ28]

i assume its using a hear exchanger as well as the built in intercooler..

is it air/water or air/air?
any provisions for a methonal setup?

the price is reasonable for what you are getting.. sheetmetal manifold intercooler.
its a ton of r@d put into it.. looks like the cobra manifold is seen this week.
legit parts:)

thats what i'm thinking. would make a great addition to an f1 where space for tubing is limited. pretty sick either way

[Pesce Nero]

the intake is to eliminate an air/air with a water/air for street driving or a ice box for drag racing. Lane said he will have a website shorty and i will post it for those interested

[WWhittle]

That would be an aftercooler.

Just sayin....

[chrisheltra]

Kinda hard to tell but there looks to be a lot of restriction there. Could be the way the pic was taken.

http://i40.photobucket.com/albums/e225/sixpackgut/lanes%20stuff/GetAttachment2.jpg

[1998ta__1991rs]

with boost it really doesnt matter, the air is going in there if it likes it or not

[BAD BOB]

i think its bc of the way the picture was taken. it looks like it is about 4in tall in the closest area when it swoops up

[s14.5gonewide]

id like to see it without the top hat on it personally. it looks like bar/fin core..
its only dropping intake temps so much regardless...

lets say u started with a 60deg intake temp... id assume with this setup and a ice/water/exchanger system.. even under higher loads(short burts) id assume ideal intake temps would be in the low 100/120deg... ideally it would be in the 70/80 at the track.

you would ice the hat down in the pits.. and do a pre ice circulation in stagingl anes.. just before u roll into the box.. ur pump the rest and apply the rest of the ice.. with that in mind you would be mid 90deg temps..

if you are running a remote mount/rear mount the temps will be lower if it is a front mount turbo temps will be roughly the same..

i would personally run a honda shorty aluminum raditor
http://www.full-race.com/catalog/product_info.php?cPath=439&products_id=481

with a meziere water/fluid pump

and some type of a ice /water chest with like an-12 lines

[Matts94Z28]

with boost it really doesnt matter, the air is going in there if it likes it or not

:hysterical: That's what she said!!