Strange Or moser?

[BigdaddyDupree]

Well since i broke the rear in my truck now i believe its a good time to step it up a notch. I dont want anything im gonna have to change later so im gonna build a 9 inch in case i step my game up. I already have a housing for a s-10 and i have the brakes covered, but i need to decide if im gonna go moser or strange.

I can get the strange 33 spline axles, axle bearings, stud kit,retaining plates and spool for 594 shipped.

I can get the same thing but moser for 540.

anyone have any preference?

[WWhittle]

You will get all kinds of different opinions but I can tell you that there isn't a racecar shop i have ever stepped foot in that uses Moser. Strange or Mark Williams but not Moser.

[Illusions]

Moser, you work hard for your money. I'd go with the least expensive unless there is a warranty difference. And make sure you get 3" long studs.

I do know it seems easy to find centers on the used market with the 31 splines. just a thought.

[BigdaddyDupree]

yeah i can get these 33 splines with the spool and all and i have a housing. so i think im gonna go that route. im gonna check with a company we go threw at work and see what i can do.

Dont take any offense to me going the 9" route hal. i mean when i called you yesterday about the 8.8 i was trying to see what i wanted to do. Now that i am thinking about doing this i wanna do it once n do it right. if i ever build a bigger motor and pile the gas on it then i want to be able to grab it from home and only break traction. no more c-clip axles for me they cost me too much damn money.

[BAD BOB]

prolly should have done an axle upgrade before gas to prevent it from happening but shit happens. moser would work fine unless you wanted to spend the extra money. i have moser c-clip axles in mine and have sprayed the shit out of it from home and still havent installed the rear end girdle. the only problem with the 9 is the extra weight

[BigdaddyDupree]

yeah i mean hinedsight is 20/20 i thought it would be able to take it for a lil while. I know the 8.8 wouldrob less power, be lighter and wouldnt cost me as much to put in and all that but at the same time i would rather just get the 9 inch done and not worry with it. build it once and build it for something more then i need and i figure ill find the next weak link. then make that one better

[BigdaddyDupree]

and should i go nodular housing? this isnt gonna be cheap by any means

[Matts94Z28]

strange

[bwelch]

If your on a budget I would go with 31 spline axles. You can get nascar center section of ebay for around $600. They come with 31 spline detroit lockers, billet pinion support, and strange N case.

[Chillerman]

Tyler,

The 9" will be a good choice to build. I've been using moser axles with no problems yet.

[BigdaddyDupree]

taking the rear end to have it cutdown and going with 33 spline moser axles and spool. hope to be up and running soon, got the axles on a deal. i had no idea buddy was a moser dealer

[Chillerman]

taking the rear end to have it cutdown and going with 33 spline moser axles and spool. hope to be up and running soon, got the axles on a deal. i had no idea buddy was a moser dealer

He sure is and gives good prices as well. He has done all my rear-end work, no problems yet. Make sure you do c-clip eliminators as well.

[BigdaddyDupree]

yeah and i went 9 inch. hoping to be going soon

[Chillerman]

yeah and i went 9 inch. hoping to be going soon

Good deal. I hope your up & running pretty soon. Buddy turns around work fairly quick.

Right now our car is now a jack stand queen, were making way for the windsor to go in. The 302 & trans. will be out by tomorrow night.

[BigdaddyDupree]

im gonna get my new rear done then step my game up

[BigHemi]

MW is the best, Strange and Moser are comparable in my opinion. I have a complete Moser Dana 60 (35 spline with spool) under the cuda that hasn't been touched in 6 years. I have a Moser 9" nodular center section going in my other car.