LS header size

[MonteC]

What size primaries would you run on a heads and cam ls1 motor? Stepped?

[1 Slow Z]

1 3/4 would be just fine IMO.

[Matts94Z28]

I would go bigger... it's not TOO much more and you will only have to do it once. You wouldn't want it to be a restriction down the road.

[BigdaddyDupree]

most s-10 swap headers are 1 7/8 at least the ones i am looking at from BRP

[1 Slow Z]

Either or would be fine, but that's just my .02

[soccerspike15]

1 7/8 period

[slowgreen99]

1 7/8 period

Damn right! If Greg said it, then id ride with it. That bitch sets records!

[1998ta__1991rs]

i'd go 1 7/8" you're going to lose some low end but you'll more than make up for it up top

[jmd]

1 7/8 arh.

[Blubird]

It doesn't matter that much. If your buying brand new might as well get the 1 7/8. If your getting used headers find the best deal don't worry if it's 1 3/4 or 7/8.

[Derek]

hey monte check this out

http://store.edelbrock.com/65683victorserieslongtubeheadersfor2000-02camarofirebird57lls1off-roadcompetitiononly.aspx

[minytrker]

I would just buy the cheapest ones you can find unless you are trying to get every last hp out of it. The hp difference in the $1k+ and the $300 headers is maybe 10hp. If your looking for the best ones, either kooks or arh stainless.

[MonteC]

WELL. They are going to be brandy new. I cant just buy these headers from anybody, they are swap headers for my monte carlo.

I have a few options to pick from, so i wanted to know what the best was to go for.

[BAD BOB]

IMHO the 1 3/4 will work just fine for motor and some NOS. once you get to a big shot or a big cube motor then worry about the bigger headers. most the time a smaller motor you wont turn really really hard so its better to have the low end to use the most of what you got. i went to 1 7/8 headers and didnt notice much change at all even on the 250 shot. but i dont know much about it since i have a ford but Greg knows so just do as "THE MAN" on radials says

[BAD BOB]

i also got a set of headers that are modified for my car but hug the motor tight so they may fit yours, if you are interested call me and we can see about checking them out. Robert 200-3196

[FRDnemesis]

hey monte check this out

http://store.edelbrock.com/65683victorserieslongtubeheadersfor2000-02camarofirebird57lls1off-roadcompetitiononly.aspx



I had a coated set of those and loved them! Easiest set of headers I've ever installed, great plug access. My only gripe was that the High Velocity Merge collectors were slip fit and they seemed to suck a little air at idle, throwing fuel trims off a bit. I've known others that didnt have my same experience with that merge collector, so maybe I just had a loose set. For the money it is the best of both worlds and if you know anyone that can do some specialized wire welding, you can have the HVMC's welded on before you even install them. Then all potential problems are cured!

[MonteC]

i also got a set of headers that are modified for my car but hug the motor tight so they may fit yours, if you are interested call me and we can see about checking them out. Robert 200-3196

let me get the motor set in the car. Then we can see how they look. What are the specs?


Im sure we will talk at the track sooner or later.

[slowgreen99]

let me get the motor set in the car. Then we can see how they look. What are the specs?


Im sure we will talk at the track sooner or later.

1 7/8" custom Bad Bob built. Ceramic coated. They look very nice.

[1998ta__1991rs]

1 7/8" custom Bad Bob built. Ceramic coated. They look very nice.

probably talking about the 1 3/4 ones he had before, hes probably going to need the 1 7/8 for the new setup

[slowgreen99]

probably talking about the 1 3/4 ones he had before, hes probably going to need the 1 7/8 for the new setup

Oh, well I thought he mentioned 2" primaries? Maybe not then.

[MonteC]

My oil pan should be here tomorrow. I need to go ahead and pull the trigger on the swap kit, get that on its way here. Gotta load the car and and haul it to the shop, pressure wash the underbody and engine bay.

Hey robert do you want a bobs masterbend custom exhaust for a gbody? Ive got one....

[Matts94Z28]

No way... the Monte is about to move?!?!! Did you bump your head?

[MonteC]

Sold the Fiero. Ive got a guy working on the transam, he hauled it to his house. Now i have room at the shop.

Got two more cars i need to sell though....

[soccerspike15]

rob you need to go to the doctor and get checked