|
08-26-2013, 09:22 PM
|
#1 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
Aluminum block ls1 motor with spun bearing and more ls parts....
I have a 2002 ws6 90k mile (supposedly on all that, I can't verify) aluminum block LS1 with one spun rod bearing. It didn't damage the crank and I have a replacement piston and rod for it.
Asking: $400 obo for it I also have a 5.3 truck intake with rails/injectors/t.b., a truck oil pan, timing cover, rear cover, camshaft, oil pump, valve covers and dipstick $50 for all I have a set of untouched 241 casting complete heads with valve covers, stock rockers and rocker trays, and stock pushrods $150 obo Thanks, Nathan 912-8 five 6-2601
__________________
Working on junk.... |
|
|
|
09-07-2013, 06:07 PM
|
#2 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
$500 for it all if you come get it.
__________________
Working on junk.... |
|
|
|
|
09-08-2013, 08:19 AM
|
#3 |
|
Senior Member
Join Date: May 2012
Posts: 1,239
|
Pm'd
__________________
LSX Mustang in process. 
|
|
|
|
|
09-08-2013, 09:05 AM
|
#4 | |
|
Senior Member
Join Date: Oct 2009
Location: Aiken
Posts: 7,002
|
Quote:
|
|
|
|
|
|
09-11-2013, 05:52 AM
|
#5 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
I still have it and need it gone soon. I'm moving in a month and need to get rid of as much junk as possible....
__________________
Working on junk.... |
|
|
|
|
09-15-2013, 07:52 AM
|
#6 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
$450 for it all...
__________________
Working on junk.... |
|
|
|
|
09-21-2013, 12:05 PM
|
#7 |
|
Senior Member
Join Date: Aug 2010
Location: Ladson
Posts: 734
|
Were you planning on putting all this together for a complete motor?
|
|
|
|
|
09-21-2013, 11:06 PM
|
#8 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
Yep, I was planning on throwing it together for my fj40 Landcruiser project. I have since gotten a good low mile 350 for cheap and decided to make it simple an use the 350.....
It's still for sale. $400 firm for it all.
__________________
Working on junk.... |
|
|
|
|
10-07-2013, 09:35 AM
|
#9 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
$300 for shortblock. Will need new rod bolts since I removed all the rods to check them out. Crank checked out good, I installed a good piston/rod in place of the spun one. So shortblock is complete, but I would replace all bearings ( none were bad), and the rod bolts.
$100 for 241 casting heads/rocker/pushrods/truck pan/truck intake/etc
__________________
Working on junk.... |
|
|
|
|
10-13-2013, 11:48 AM
|
#10 |
|
Senior Member
Join Date: Apr 2012
Location: Guyton, GA
Posts: 1,412
|
SOLD!
__________________
Working on junk.... |
|
|
|
 |
|
|
Linear Mode
